This guide will walk you through installation notes, troubleshooting tips, and special features for installing your VHEDIA head unit into a Toyota LandCruiser 200 Series 2007-2015 Sahara.
Installation Video (1 Camera Model)
Installation Video (4 Camera Model)
Which Wire Goes Where
This guide runs through every plug, cable, and harness so you know exactly where everything goes.
Because the Sahara has more plugs than most vehicles, this walkthrough helps you double-check each connection — the most common cause of install issues.
What You’ll Learn:
Identifying the different Sahara plug variations
Matching factory plugs to the Vhedia harness
Connecting the CANBUS boxes + secondary harness
Radio, camera, USB, and main power plugs
Which plugs you don’t use (and why)
How to connect everything at the head unit side
What to test after wiring (sound, reverse camera, SWC, AC controls)
Perfect for new installers and DIYers — follow along and tick off each plug as you go
Video Guide:
If you need help or troubleshooting, just send us photos of your wiring from multiple angles and we’ll get you sorted.
Wiring Diagram for Toyota Land Cruiser 200 Sahara With Single Camera System
This guide provides the correct wiring setup for a Toyota LandCruiser 200 Series Sahara (2007–2015) with a single camera system. Refer to the wiring diagram photos and video guide below to ensure proper connection of all cables and plugs.
Factory Head Unit
Main Harness to VHEDIA Head Unit
Factory Plugs to Main Harness
Camera Box
Hazard and CANBUS Cable
Radio Antenna
Auxiliary Cables
Video Guide:
Common Issues & Fixes
AC Resetting When Changing Temperature or Fan Speed
When installing this head unit, you need to connect the TEMP cable correctly to prevent any issues with the factory settings/controls of the vehicle such as AC Temperature. The TEMP cable included in the kit comes with two plugs: a 10-pin plug and an 8-pin plug. The correct plug to use depends on your factory head unit.
If your factory head unit looks like this, use the 10-pin plug:
If your factory head unit looks like this, use the 8-pin plug:
Installation Steps
Locate the TEMP cable in the kit.
Identify whether your factory head unit requires the 10-pin or 8-pin plug.
Insert the corresponding plug into the designated AC temperature port.
Ensure the connection is secure before proceeding with the installation of the head unit.
Reversed/Flipped AC Vents Controls
If adjusting the driver’s side AC vents changes the passenger side AC vents instead (and vice versa), follow these steps to fix the issue:
Tap the System icon on the list off apps.
Go to System.
Tap Setting guide.
Go to Vehicle Type Protocol Selection.
Enter 8861.
Tap the gear icon on the top right.
Change "Temperature display on both sides of the ... " and "Temperature control on both sides of the ..." to Normal or Reverse (depending on your car's driving orientation).
Swipe down from the top of the screen with one finger to open the Notification and Dropdown Menu. Then tap Reboot for the changes to reflect.
"No Signal" Error When Going On Reverse
This can happen if the reverse camera cable is not connected properly or not connected at all.
Check the 360 Camera Connector
If your vehicle has both blue and white connectors, connect the white plug.
If only a blue connector is present, connect the blue plug.
Verify the Yellow RCA Connection
Ensure that the yellow RCA plug from the grey connector (not the white big plug) is connected to the reverse camera input on the head unit.
Head Unit Displays An Aftermarket 360 Camera View Instead Of The Factory 360 Camera When Going On Reverse
This can happen if the aftermarket 360 view setting is enabled and you need to disable it.
1. Go to System.
Navigate to System > Factory Setting.
Enter 7890 as the passcode and press OK.
Locate "Aftermarket HD 360".
Select "Close" to disable the aftermarket 360 camera setting.
Click Save and restart.
7. After the head unit reboots, shift the vehicle into reverse and check if the factory 360 camera view is now displayed correctly.
Static Noise While Listening To Music
Need to adjust the VOL setting to reduce or eliminate the static noise.
1. Access the All Apps Menu
Navigate to the home screen of your head unit.
Tap on All Apps to open the full list of applications.
2. Open Car Information
Scroll through the apps and select CarInformation.
3. Adjust AMP Settings
Within CarInformation, locate and open AMP Settings.
4. Modify Volume Settings
Find the VOL option.
Change the value to -45.
5. Save and Test
Ensure the settings are applied.
Play music to check if the static noise has been reduced or eliminated.
360 Camera View Not Triggering in Reverse
Need to ensure that the 360 Panoramic Reversing Year is set to 2016.
Confirm Factory 360 Camera Functionality
Before proceeding with the setup, ensure that your vehicle is equipped with a factory 360-degree camera system and that it was working properly before installing the new head unit.
Adjust the 360 Camera Settings
Open All Apps on the VHEDIA head unit.
Select CarInformation.
Navigate to Vehicle Settings.
Look for the option "360 Panoramic Reversing Year". Change the setting to 2016.
Restart the vehicle, shift into reverse, and check if the 360 camera view is now displayed correctly.
Climate App Not Opening/Functioning Properly
This can happen if the car model/protocol setting is incorrect.
Go to System.
Tap System and go to Setting guide.
Tap Car model/protocol and enter the passcode 8861.
Select the Correct Configuration
On the first column from the top left, select TangDu.
On the second column, select Toyota.
On the first column from the bottom left, select Land Cruiser.
On the second column, select 07-15 TOP(4ZONE).
Save and Reboot
After selecting the correct settings, confirm and restart the head unit.
Need further assistance? Reach us out on our support channels:
Live Chat on our website (https://vhedia.com.au/): Mon–Fri, 7 AM–5 PM (Perth time)
Phone Support: 1800 577 415, Mon–Fri, 7 AM–3 PM (Perth time)
Email: hey@vhedia.com.au