This guide will walk you through installation notes, troubleshooting tips, and special features for installing your VHEDIA head unit into a Toyota Landcruiser 200 Series 2015-2022 Sahara & VX.
Installation Video
Which Wire Goes Where
Common Issues & Fixes
360 Camera View Not Triggering in Reverse
Need to ensure that the 360 Panoramic Reversing Year is set to 2016.
Confirm Factory 360 Camera Functionality
Before proceeding with the setup, ensure that your vehicle is equipped with a factory 360-degree camera system and that it was working properly before installing the new head unit.
Adjust the 360 Camera Settings
Open All Apps on the VHEDIA head unit.
Select CarInformation.
Navigate to Vehicle Settings.
Look for the option "360 Panoramic Reversing Year". Change the setting to 2016.
Restart the vehicle, shift into reverse, and check if the 360 camera view is now displayed correctly.
White Or Blank Display After Connecting Factory Reverse Camera
Need to disable the "Aftermarket HD 360" option from the factory settings.
1. Open Settings
On your head unit, navigate to Settings.
2. Access Factory Settings
Go to System > Factory settings.
Enter the factory settings PIN: 7890.
3. Disable the "Aftermarket HD 360" Option
Locate the option "Aftermarket HD 360".
Set it to Close.
4. Save and Reboot
Scroll down and press Save.
Reboot the head unit to apply the changes.
VIDEO GUIDE:
How to Set Steering Wheel Controls (SWC)
Go to Settings.
Select System.
Tap on Steering wheel setting (also referred to as Steering Wheel Control Settings).
On the Steering wheel setting screen, you’ll see virtual buttons representing common steering wheel functions (e.g., Volume Up, Volume Down, Mode, Track Forward/Backward, etc.).
Assign Each Button
Tap on a virtual button on the screen (e.g., Volume Up).
Immediately after, press the corresponding physical button on your steering wheel.
The head unit will recognise and map that steering wheel button to the function.
Repeat this process for all the other steering wheel buttons you want to configure.
Final Checks:
You can test the buttons right after setup to ensure they’re working correctly.
If a button doesn't register, try reassigning it by repeating the same steps.
Avoid pressing multiple steering wheel buttons at once during setup.
How To Map Unresponsive Buttons
Here's a troubleshooting guide on how to map unresponsive buttons on your T-1829GH-A13 head unit.
Go to System on the head unit's home page.
Tap System on the upper right part of the screen.
Scroll up and toggle ON Panel key Learning switch then tap Panel key Learning.
Scroll left or right and tap the key that you would want to learn and then tap/press the button for the changes to reflect.
Weak Or No Radio Reception
Some models rely on an automatic antenna booster that needs to be enabled for the radio signal to work properly. Follow the steps below to get your radio reception sorted:
Go to System.
Tap General and toggle ON Automatic antenna.
Final Checks:
After enabling the setting, restart the Radio app and scan again for stations.
Make sure the antenna connector is properly seated at the back of the head unit.
Climate App Not Opening/Functioning Properly
This can happen if the car model/protocol setting is incorrect.
Go to System.
Tap System and go to Setting guide.
Tap Car model/protocol and enter the passcode 8861.
Select the Correct Configuration
On the first column from the top left, select TangDu.
On the second column, select Toyota.
On the first column from the bottom left, select Land Cruiser.
On the second column, select 07-15 TOP(4ZONE).
Save and Reboot
After selecting the correct settings, confirm and restart the head unit.
Need further assistance? Reach us out on our support channels:
Live Chat on our website (https://vhedia.com.au/): Mon–Fri, 7 AM–5 PM (Perth time)
Phone Support: 1800 577 415, Mon–Fri, 7 AM–3 PM (Perth time)
Email: hey@vhedia.com.au